







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Bathroom Remodeling: The Westminster Owner’s Guide
Schluter-compatible bathroom remodeling in Westminster runs $9,000 – $28,000 installed, depending on how much of the wet area we rebuild and whether we’re working over an existing bonded membrane or starting fresh. We don’t keep parts on a truck – we quote the exact Schluter profiles and membranes your job needs, in writing, before any work starts. Most owners find us after a shower curb starts weeping, grout joints along the floor line go dark and stay dark, or a loose tile sounds hollow underfoot. That hollow sound is usually the tell: the bonded waterproofing layer has failed somewhere beneath the tile, and no amount of re-grouting fixes it. A written price and a call to (833) 954-5086 will tell you what you’re actually facing.
Which Schluter Models This Applies To

Schluter’s wet-area systems show up in Westminster bathrooms in a few recognizable configurations, and the compatibility question is almost always about matching the right membrane and profile to the substrate you have, not matching a part number to a model year. The main ones we see:
- Kerdi-Board and Kerdi membrane – the bonded sheet waterproofing over cement board or drywall. Kerdi-Board is the foam-backed panel version; Kerdi membrane is the thin sheet you thinset directly to the substrate.
- Kerdi-Fix and Kerdi-Band – the sealant and the reinforcing band for seams, corners, and the critical floor-to-wall junction.
- Kerdi-Line and Kerdi-Drain – linear and point drains that integrate into the waterproofing layer, not sit on top of it.
- Ditra and Ditra-Heat – the uncoupling membrane for tile floors and heated floors, which is a different failure mode entirely from wet-area waterproofing.
To identify what you have, pull the label off any leftover membrane or look at the profile edge at a curb or niche – Schluter prints the system name and thickness there. Sizes matter: Kerdi-Board comes in 1/2-inch and 2-inch thicknesses, and using the wrong one at a shower bench or curb changes the whole build-up. The OEM-versus-aftermarket call is real, and it’s not close. Generic sheet membranes sold as “equivalent” often miss the perm rating and the fleece bond that make Schluter systems work, and we’ve pulled plenty of them out of Westminster showers that failed inside two years. We specify Schluter’s own components because the manufacturer spec and warranty are traceable, and our 365-Day Done Right Promise sits on top of that. We’re an independent service provider, not affiliated with Schluter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Bathroom Remodeling Is Failing
Waterproofing failures don’t announce themselves. They telegraph, and the signs stack up before a ceiling below starts to sag. Here’s what to watch for in a Westminster bathroom:
- Grout that stays dark after a shower. The tile isn’t the problem – moisture is trapped in the substrate and can’t dry. That means the bonded membrane has a breach at a seam, a corner, or a fastener penetration.
- Hollow or loose tile, especially near the drain and curb. A dead sound means the thinset bond has broken down. On a Kerdi assembly, that usually traces to a membrane that wasn’t fully embedded during install, not a tile defect.
- Efflorescence or white crust along the floor line. Mineral salts wicking through grout mean water is moving through the assembly. Westminster’s hard water makes this more visible here than in softer-water cities around the county.
- A shower pan that flexes or “gives” slightly. The slope has failed and water is pooling under the tile instead of running to the drain. Left alone, this is the failure that rots joists and shows up as a stain on the ceiling below.
- Musty smell that returns after cleaning. Mold in the wall cavity behind the tile, fed by chronic damp. No grout sealer or bleach scrubbing reaches it, because the membrane isn’t doing its job.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A full Schluter-system bathroom remodel in Westminster is $9,000 – $28,000. A walk-in shower installation alone runs $4,500 – $12,000; a tub-to-shower conversion is $3,500 – $10,000; a straight shower replacement where the footprint stays put is $3,000 – $8,500. A smaller bathroom remodel lands at $5,000 – $12,000.
What drives the number up is scope, not parts. Three things move it most: how much substrate we have to replace once the tile comes off, whether the drain has to be relocated, and whether you’re staying in the current footprint or going to a linear drain that needs a re-slope. The written price you get before work starts covers tear-out, substrate, Schluter membrane and profile, thinset, tile setting, and finish. It doesn’t move at the door.
Every completed job carries the 365-Day Done Right Promise: if the work fails inside a year, we come back and correct it at no charge. That’s the whole point of the guarantee, and it’s in writing before the first tool comes out.
DIY or Call Us?
A homeowner can safely check a few things: run your hand along the caulk at the curb and floor, look for movement in the shower pan, and press on a suspect tile to listen for a hollow ring. What you shouldn’t do is start prying up tile to “see what’s underneath.” Wet-area waterproofing isn’t visible once it’s covered, and once you break the membrane you’ve turned a localized repair into a full rebuild. This is real damage territory – a failed shower pan in a second-floor Westminster bathroom can rot framing and damage the ceiling below before the tile ever looks wrong.
If a tile’s already loose or the pan flexes, call (833) 954-5086. A live person answers 24/7, and a written estimate is free.
FAQs

How long does a Schluter shower system last? A properly installed Schluter wet-area assembly should hold for 25 years or more – the membrane itself isn’t the usual failure point; the installation is. In Westminster’s climate, the biggest threats are sun load through a bathroom window drying the sealant joints faster than you’d expect, and hard water stressing grout lines. Call (833) 954-5086 if yours is past 15 years and you’re seeing any of the signs above.
Can it be repaired instead of replaced? Sometimes. A localized membrane breach at a curb or drain can be repaired without a full tear-out, but only if the failure is isolated and the substrate beneath is still sound. Once water has tracked under tile for a season or more, the substrate is usually toast and a rebuild is the honest answer. We’ll tell you which one you’re facing in the estimate.
How long does the swap take? A shower-only replacement in a Westminster bathroom is typically 5 to 10 working days, depending on tile choice and how much substrate has to come out. A full bathroom remodel runs 3 to 5 weeks. We give you the schedule in writing with the price.
How do you source the Schluter components? We quote from the documented roster of materials your job actually needs, and the parts list is part of the written scope you receive before work begins. We don’t stock parts or carry them on a truck – we order to spec so the membrane, profile, and drain all match the assembly. Call (833) 954-5086 to start a written estimate.
Written by the team at Bradford Remodeling Co Westminster, serving Westminster and nearby areas.












