







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Kohler Bathroom Remodeling: The Westminster Owner’s Guide
A Kohler bathroom remodel in Westminster runs $9,000 – $28,000 installed, with a small bath landing between $5,000 – $12,000. Kohler fixtures are built to standard rough-in dimensions, so matching a replacement toilet, faucet, shower valve, or vanity to your existing plumbing is usually straightforward once we confirm the model line. Westminster homeowners typically call us after a Kohler part gives out quietly: a faucet that drips after the handle is shut, a toilet that runs for a few seconds on its own, or a shower valve that has lost its cold-to-hot sweep. We’re an independent remodeling company, not affiliated with Kohler, and we install to the manufacturer’s spec with a written price before work starts.
Key Takeaways
- Typical installed range: $9,000 – $28,000 for a full Kohler bath; $5,000 – $12,000 for a small bath.
- Compatibility: Kohler publishes spec sheets by model number, and most modern lines use standard rough-ins.
- Warranty: Every completed remodel carries the 365-Day Done Right Promise in writing.
- Pricing: Written price before any work begins, no numbers that move at the door.
Which Kohler Models This Applies To

Kohler’s bathroom lines split into a few families worth knowing by name: the Memoirs and Devonshire collections for classic styling, Santa Rosa and Cimarron for efficient toilets, Purist and Loure for contemporary faucetry, and the Katalyst showerheads. Each collection typically spans multiple rough-in sizes. A Cimarron toilet, for example, comes in both a 10-inch and a 12-inch rough-in, and that number is the distance from the finished back wall to the center of the drain bolts. Get it wrong by half an inch and the tank won’t seat flush to the wall.
To identify your model, look under the toilet tank lid or behind the faucet escutcheon for a model number sticker. Kohler’s website hosts spec sheets for current and discontinued models, and measurements on those sheets are what we match the new part against.
On OEM versus aftermarket: for anything with a wear surface that touches water daily (cartridges, flush valves, fill valves), we install Kohler OEM or a manufacturer-approved equivalent because the tolerances are tighter and the warranties attach. For purely cosmetic trim, a quality aftermarket piece is often fine. The decision isn’t cost alone; it’s how much risk you accept on a part that sees hundreds of cycles a week. We also install KraftMaid cabinetry, Cambria and Silestone surfaces, and Moen fixtures when the scope calls for them.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Kohler Bathroom Remodeling Is Failing
- The faucet drips after shutoff. The ceramic cartridge inside the valve body has worn its sealing faces smooth. You’ll usually see a slow bead at the spout even with the handle firmly closed.
- The toilet runs for a few seconds on its own. The flapper or the fill valve seat has degraded. In Westminster’s hard water, mineral scale builds on the valve seat faster than most owners expect, and the seal stops sitting clean.
- The shower valve has lost its temperature sweep. The pressure-balance cartridge is sticking. You’ll notice the handle feels stiff or the water stays tepid until you turn it further than you used to.
- Water pools at the base of the toilet or under the vanity. The wax ring, supply line, or shutoff valve is seeping. Left alone, moisture reaches the subfloor and the sill plate, and the repair grows from a $12 wax ring into a floor patch.
- The showerhead sprays unevenly or the flow has dropped. Scale has blocked the Katalyst or rain head nozzles. Sometimes it’s the head; sometimes it’s the supply line or a failing valve behind the wall, which is a different repair entirely.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Here’s what Kohler bathroom work typically costs in Westminster, with parts and labor written separately so you can see where the money goes:
- Full Kohler bathroom remodel: $9,000 – $28,000
- Small bathroom remodel: $5,000 – $12,000
- Walk-in shower installation: $4,500 – $12,000
- Tub-to-shower conversion: $3,500 – $10,000
- Shower replacement: $3,000 – $8,500
- Vanity installation: $800 – $3,000
The range is driven by what’s behind the wall (substrate condition, and whether the rough-in needs to move), the fixture tier you choose, tile and surface selection, and whether permits apply. A standard toilet and faucet swap sits at the low end. A full conversion with new tile, a relocated drain, and a garden tub removal sits at the high end. Every project gets a written price before work starts, and any toilet, valve, or supply-line work we complete is covered by the 365-Day Done Right Promise for a full year.
DIY or Call Us?
Some things you can check safely. Look for the model sticker, confirm the rough-in measurement with a tape measure, and shut off the water at the angle stop before inspecting a leaking supply line. A faucet cartridge swap on a Kohler single-handle faucet is within reach for a confident homeowner with the right cartridge number.
What we don’t recommend you tackle yourself: opening a wall to access a shower valve, replacing a pressure-balance cartridge behind finished tile, or any repair that involves the drain and sewer connection. A shower valve under pressure is unforgiving, and a botched rough-in means tearing out new tile. We’re background-checked and uniformed on every job, so you know exactly who’s coming through the door. Call (833) 954-5086 to schedule your free estimate.
FAQs

Most Kohler toilet fill valves and flappers last 5 – 8 years before the seal degrades; ceramic faucet cartridges often reach 10 years, and shower valves can go longer if water pressure stays steady. In Westminster, hard water tends to shorten the valve and flapper lifespan because mineral scale wears the sealing surfaces faster.
Yes. Faucet cartridges, toilet flappers, and fill valves are all serviceable parts, and a repair often costs a fraction of replacement. Repair makes sense when the body and finish are sound; replacement wins when the rough-in has failed or a discontinued model can’t source a matching cartridge.
A toilet valve replacement runs 45 minutes to a couple of hours; a faucet or shower valve swap takes 2 – 4 hours when the wall stays closed. Anything that opens the wall for rough-in access pushes to a full day or more. We’ll give you the realistic window before the crew arrives.
We pull the spec sheet directly from Kohler using your model number, confirm the rough-in and dimensions against what’s actually in your bathroom, and order the OEM part or a manufacturer-approved equivalent. If your model is discontinued, we source a compatible replacement and explain the fit before installing it. Call (833) 954-5086 for a free estimate on any part or full remodel.
Written by the team at Bradford Remodeling Co Westminster, serving Westminster and nearby areas.












