







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Home Additions & ADU: The Westminster Owner’s Guide
We build and finish Boral-spec home additions and ADUs in Westminster in the $45,000 – $130,000 range for a addition and $90,000 – $220,000 for a detached ADU, and the conversation almost always starts the same way: a homeowner calls because a Boral-trimmed addition or ADU is showing a problem they didn’t plan for. Often it’s a soffit panel that’s gone chalky and started to lift at the fascia, or a piece of Boral siding on the new wing that’s cupping after two winters of marine air. Sometimes it’s a failing transition where the addition ties into the original house and the trim has pulled away from the substrate. This page is for the Westminster owner who already has Boral product on the structure and needs the failing piece identified, priced honestly, and replaced by someone who reads the spec sheet. Bradford Remodeling Co Westminster is an independent contractor and is not affiliated with Boral.
Key Takeaways
- Boral makes exterior trim, siding, and cladding products; the round numbers below are for the failing component and the labor to replace it, not a whole new addition.
- Most failures we see in Westminster trace to moisture, sun, or a bad original install, not to the Boral material itself.
- We give a written price before any work starts, and the replacement carries the 365-Day Done Right Promise.
Which Boral Models This Applies To

Boral’s exterior line runs through several product families, and the panel or trim you have determines which replacement piece is correct. The common ones on additions and ADUs in this market are Boral TruExterior trim and Boral Versetta Stone veneer, plus Boral’s composite siding profiles. The gotcha is that TruExterior has changed formulation and profile dimensions over its production life, so a 5/4-by-4 board from an older run may not match the current stock in thickness or edge detail. Before we order anything, we read the mill stamp or the label on the back of the panel, measure the actual face width and thickness with a caliper, and check the profile against the current spec. For Versetta Stone, the interlock pattern and the color lot matter: a replacement panel from a different lot will read as a slightly different shade in direct afternoon sun, which is why we order the full course when a color match is critical.
There’s no such thing as an aftermarket Boral equivalent that meets the same fire and moisture ratings, so we stay OEM on this product. What we do control is sourcing: we spec from the manufacturer’s current catalog, not a discontinued rack at a big-box store, and we confirm the profile before the truck rolls. If you’ve also got KraftMaid cabinetry or Cambria surfaces going into the finished ADU, the same spec-first discipline applies there. Bradford Remodeling Co Westminster handles the sourcing and the install as one scope.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Boral Home Additions & ADU Is Failing
These are the failures Westminster homeowners call us about most, and each one points to a cause worth knowing before you spend money on a fix.
- Chalky, faded panels on the south or west face. UV exposure breaks down the surface finish over time. Westminster’s inland sun load is higher than the coastal reputation suggests, and an unprotected south-facing wall takes the worst of it.
- Cupping or bowing along a panel edge. Moisture is getting behind the cladding, usually at a caulk joint or a missing flashing detail at the roof-to-wall transition. The panel is the symptom; water intrusion is the problem.
- Trim pulling away from the substrate. Fasteners have backed out or the substrate has swelled. On an addition, this often shows up at the tie-in to the original house, where two different wall assemblies meet.
- Visible gaps at the interlock of stone veneer. The scratch coat or lath behind the veneer wasn’t bedded correctly, so panels shift. This one rarely fixes itself with a patch.
- Soft spots or discoloration near the base of a wall. Water is wicking up from a grade that wasn’t sloped away from the addition. This is a drainage problem the cladding can’t solve on its own.
If more than one of these shows up on the same wall, the honest answer is that the cladding is doing its job and the assembly behind it needs attention. We’d rather tell you that than sell you a panel swap that masks the real issue.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

A targeted Boral trim or cladding replacement on a Westminster addition or ADU typically lands inside our home addition range of $45,000 – $130,000 only when the scope is larger than a single component. For a focused repair or a partial re-clad on a finished structure, the number is driven by three things: how many linear feet or square feet are affected, whether the substrate behind the failing piece is sound, and whether the fix requires re-flashing or re-caulking a whole elevation to stop the water that caused the failure.
Here’s how the range breaks down and what drives it:
- Area affected: a few feet of fascia trim is a different job than a full wall of veneer.
- Substrate condition: if the sheathing behind the Boral is soft or wet, that has to be corrected before new cladding goes on.
- Color-lot matching: a full-course replacement costs more than a patch but avoids a visible shade break.
- Access and height: second-story work and tight side-yard access add labor.
Every quote from us is a written, line-item price before any work starts, with the material and the labor separated so you can see what you’re paying for. If the substrate is worse than the surface suggested, we stop and show you before the price moves. The 365-Day Done Right Promise covers the replacement for a full year: if the install fails within that window, we come back and correct it at no charge.
DIY or Call Us?
There’s a real split here, and we’ll be straight about it. You can safely walk the wall, photograph the failing panels, check that grade slopes away from the addition, and note where caulk has failed at joints. That information is useful and it costs you nothing. What we don’t recommend is climbing a ladder to pull a panel off a second story or prying at veneer to see what’s behind it. Cladding work involves working at height, cutting material, and getting flashing and moisture barrier right on the first pass. A panel that goes back on without the correct flashing doesn’t fail right away, it fails in the next rainy season, and then you’ve paid twice. If you’re not comfortable on a ladder or you can’t read what’s behind the gap, that’s the moment to call.
Call (833) 954-5086 and a live person answers, day or night. We’ll talk through what you’re seeing and schedule a free estimate. If the failing part is somewhere you can’t safely reach, say so, and we’ll plan the inspection around that.
FAQs

How long does Boral exterior cladding last in Westminster? Expect 20 to 30 years on a properly installed Boral panel in this climate, provided the moisture barrier and flashing behind it were done correctly. The material holds up well; the assembly is what shortens its life. Call (833) 954-5086 for a free estimate if yours is failing well before that window.
Can the failing Boral panel be repaired instead of replaced? Sometimes yes. A localized fastener issue or a failed caulk joint can be corrected without replacing the panel. Cupping, soft substrate, or shifted veneer usually means replacement. We’ll tell you which one you’re looking at during the estimate, and the price comes in writing before we start.
How long does a Boral component swap take? A single trim or fascia section is often a one-day job. A partial wall of siding or veneer typically runs two to four days, depending on substrate repairs and access. We give you the timeline in the written scope so there are no surprises. Call (833) 954-5086 to get a date on the calendar.
How do you source the replacement Boral part? We read the label or mill stamp on the existing component, measure the profile, and order the matching current Boral product from the manufacturer’s catalog, confirming the color lot where a match matters. We don’t pull a discontinued substitute to save a dollar. Call (833) 954-5086 for a free estimate and we’ll confirm the exact part before anything is ordered.
Whether you’re re-cladding a Boral-trimmed addition in Westminster or finishing a new ADU, the price comes in writing before any work starts, the crew is background-checked and uniformed, and the finished work carries the 365-Day Done Right Promise. Bradford Remodeling Co Westminster is part of the Garrison Partners family and held to The Garrison Standard on every job. Call (833) 954-5086 today to schedule your free estimate.
Written by the team at Bradford Remodeling Co Westminster, serving Westminster and nearby areas.












