







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Unilock Home Additions & ADU: The Westminster Owner’s Guide
Bradford Remodeling Co Westminster installs Unilock-compatible home additions and ADUs throughout Westminster, with typical projects running $45,000 – $130,000 depending on size, foundation work, and site access. We’re an independent contractor, not affiliated with Unilock. Most Westminster owners don’t start by shopping for an addition, though. They start with a symptom: a hairline crack running through the color band of a Unilock paver patio wall abutting the addition, a rear step that has dropped a half-inch, or a wet stain climbing the base course after a rainy week. That crack or drop usually traces back to a failed base or a cracked structural block, and it tells you the hardscape and the structure it ties into are settling out of agreement.
Which Unilock Models This Applies To

Unilock makes dozens of wall block lines, and the part that fails depends on which line your addition or ADU was built against or integrated with. Westminster projects we see most often tie into three families: Unilock’s Pisa2 and Pisa Stone retaining-wall systems (used around ADU window wells and grade changes), Brussels Dimensional Series wall block (common on raised patios abutting home additions), and Eden Stone and Rivercrest modular walls for decorative aprons and step risers. Each has a different block width and cap profile, and they don’t interchange.
To confirm your line, check for a stamped or imprinted mark on the face of an exposed block or the broken edge of a cap. Measure block height and length with a tape – Pisa2 runs at a different dimensional profile than Brussels, and a mismatched replacement shows as a visible step in the wall face within a season. On the OEM-vs-aftermarket call: Unilock doesn’t manufacture every structural or anchoring component in its assemblies, so the correct replacement usually means the Unilock block plus a compatible retaining clip or geogrid tie, not a generic paver. That matters in Westminster’s expansive clay soils, where a mismatched tie lets the base course shift.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Unilock Home Additions & ADU Is Failing
These are the symptoms that tell us which component is past its service life. Each points to a different cause:
- Crack running through a block face or cap. Usually a base course that wasn’t compacted to spec, or freeze-thaw cycling in Westminster’s cool-wet winters opening a hairline to a full split within three seasons.
- Step or grade drop along the wall that abuts the addition. Settlement in the base material, or a missing geogrid tie allowing the top two courses to lean forward into the addition’s foundation zone.
- Water staining or efflorescence climbing the base course. Poor drainage behind the wall, meaning water sat against the base and softened the compacted aggregate underneath.
- Crumbling mortar or a gapped joint where the Unilock meets the addition framing. Movement differential between masonry and the framed wall, which stresses the joint and lets water in.
- A visibly leaning cap or top course. Displaced block, a missing anchoring clip, or a base failure that has progressed past the point where re-laying a single cap holds.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Replacing the failed Unilock component and correcting the base behind it runs $45,000 – $130,000 on a full home addition in Westminster, or $90,000 – $220,000 for a full ADU build where the wall component is part of the scope. Scope drives the range: the block itself is the smallest line item on a wall-and-structure job, and the range reflects foundation work, drainage correction, permit and inspection costs, and finish tie-in. We give you a written, line-item price before work begins – no numbers that move at the door.
What’s included: removal and disposal of the failed block and saturated base, new compacted aggregate at spec, replacement Unilock block and compatible tie hardware, drainage correction, finish match to the existing wall, and a written scope you keep. If the work fails inside 12 months, the 365-Day Done Right Promise covers a return visit at no charge.
DIY or Call Us?
What you can safely do yourself: photograph the crack, note where water is pooling, measure the block dimensions, and check for a surface stamp to identify the Unilock line. What goes wrong on a DIY repair of a load-bearing wall or addition foundation component is the base. You can’t repair a failing base course by re-setting a single block – the aggregate underneath has to be removed, re-compacted to spec, and re-tied to the structure. Doing that wrong on a wall that abuts a home addition or ADU foundation can move the load path and compromise the structure it protects, which is a real safety and permit concern, not a cosmetic one. If your wall leans or the addition footprint has shifted, stop and call a trained professional.
Call (833) 954-5086 for a free estimate – our technicians have up to 22 years of experience and will identify the exact part, not guess at a replacement.
FAQs

A properly installed Unilock wall block and tie assembly typically lasts 20 – 30 years in Westminster’s climate. Cracking, leaning, or base settlement within five to seven years points to base compaction, drainage, or tie problems rather than the block itself wearing out. Call (833) 954-5086 for a free inspection if you’re inside that window and seeing movement.
Sometimes – a single cracked cap or a minor joint crack can often be repaired. Structural-leaning blocks, or a base failure with water intrusion, usually require removal down to the base and re-build. We’ll tell you which one you’re facing in writing before any work starts. Estimates are free.
Most component-level replacements run one to three days; a base correction on an addition or ADU tie-in takes longer, typically one to two weeks once the scope is written. Your timeline is confirmed in the written scope before work begins. Call (833) 954-5086 for a project-specific timeline.
We work through documented material channels and match your Unilock line from surface markings and measured block dimensions, then confirm the correct compatible component before ordering. If the exact line is discontinued, we’ll tell you and offer the closest confirmed match in writing. Call (833) 954-5086 – estimates are free.
We also work with KraftMaid, Cambria, and Silestone on interior scope, and every Bradford Remodeling Co Westminster project carries the 365-Day Done Right Promise in writing. Call (833) 954-5086 for your free estimate.
Written by the team at Bradford Remodeling Co Westminster, serving Westminster and nearby areas.












