







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Schluter Home Additions & ADU: The Westminster Owner’s Guide
We build and finish Schluter-system home additions and ADUs in Westminster, with fully installed projects typically landing between $45,000 and $130,000 depending on square footage, foundation type, and wet-area scope. Schluter isn’t a part that “fails” the way a garage spring snaps – it’s the waterproofing and uncoupling layer under your tile, and when it’s installed wrong or breaks down, you find out through cracked grout lines, loose tile, and efflorescence creeping up a shower wall in a Westminster addition or ADU. Most owners discover the problem months after move-in, when a hairline crack in a new bathroom floor starts walking from one tile to the next.
Key Takeaways
- Schluter systems (DITRA, KERDI, KERDI-BOARD) are substrate-level products, not appliances – installation quality decides whether they last.
- Westminster’s clay soils and seasonal moisture swings punish a bond coat that wasn’t applied correctly.
- A failed Schluter layer rarely means tearing out the whole addition – it means isolating and rebuilding the affected wet area.
- Written price before work starts, and a 365-Day Done Right Promise on the finished install.
Which Schluter Models This Applies To

The Schluter lineup that shows up in Westminster additions and ADUs breaks into four families, and knowing which one you’re looking at decides the fix.
DITRA and DITRA-HEAT are the uncoupling and heated-floor membranes that go under tile. DITRA comes in 3’3″ x 32’8″ rolls and in sheets; DITRA-HEAT is the matted version with heating cable clips. If you’re trying to match a replacement, check the printed roll edge – Schluter stamps the series and lot on every roll, and DITRA-HEAT mats are marked separately from plain DITRA.
KERDI is the waterproofing membrane for showers and wet areas, sold in rolls and in KERDI-BAND strips for seams and corners. KERDI-BOARD is the foam backer panel (in 1/2″, 5/8″, and thicker) that replaces cement board behind tile. KERDI-LINE and KERDI-DRAIN are the linear and point drains that tie into the membrane.
OEM vs. aftermarket: Schluter’s own membranes are the only ones with their exact fleece and anchoring pattern. Third-party “uncoupling membranes” exist and can work, but the warranty doesn’t follow them the same way, and mixing brands across a shower floor is where Westminster homeowners get burned. Match the Schluter series to the assembly, not just the shape.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your Schluter Home Additions & ADU Is Failing
These are the five symptoms we see most often when a Schluter assembly goes bad in a Westminster addition or ADU.
- Grout cracking in a straight line across the floor. That’s the uncoupling layer letting movement through to the tile. Usually the membrane wasn’t fully bonded or the substrate below it flexed.
- Hollow-sounding tile when you tap it. Air pockets under DITRA or KERDI mean the thin-set didn’t make full contact. Tap a new addition’s floor with a coin handle and listen for the difference.
- Efflorescence or white powdery staining on a shower wall. Moisture is getting behind the KERDI at a seam or corner. Westminster’s hard water makes the mineral bloom more visible here than in softer-water areas.
- Loose or lifting tile at a shower curb or niche. The KERDI-BAND corner overlaps weren’t sealed correctly, and water has been wicking under the edge.
- Water staining on the subfloor or framing beneath a wet area. The membrane is breached and has been leaking slowly. This is the one that needs attention now, not next season.
Replacement Cost & What’s Included

Repairing a failed Schluter assembly in a Westminster addition or ADU runs $2,000 to $9,000 for a localized shower or floor rebuild, and full home additions that need the wet areas redone with a corrected Schluter install land in the $45,000 to $130,000 range when they’re part of a larger build.
What drives the range: square footage of affected tile, whether the substrate has to come up to the framing, and whether you’re rebuilding one shower or a bathroom plus a laundry room. KERDI-BOARD replacement panels and new DITRA membrane are line-itemed separately from labor, so you see the parts cost and the crew cost as two numbers. No hidden line for “miscellaneous substrate.”
Every Schluter install we complete carries the 365-Day Done Right Promise in writing. If the membrane or the tile over it fails within that year, we come back and correct it at no charge. Faucets and cabinetry brands like Kohler, Moen, and KraftMaid are covered by their own manufacturer warranties on top of ours.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
You can safely inspect a Schluter floor or shower yourself: tap for hollow spots, look for efflorescence at grout joints, and check the subfloor below a wet area for staining. Those checks cost nothing and tell you whether the assembly has a problem. What you shouldn’t attempt is the repair itself. Removing a DITRA or KERDI layer without damaging the substrate, then re-bonding a new membrane with the correct thin-set and full coverage, is where homeowners get into trouble – a partial re-bond lets the same failure come back within a year.
One honest note: Schluter assemblies aren’t dangerous to handle, but they’re unforgiving of a bad install, and the water damage a breach causes can cost far more than the original job. If you’ve found hollow tile or efflorescence in a Westminster addition, call us at (833) 954-5086 and we’ll give you a written price for the repair before we touch anything.
FAQs

A correctly installed Schluter membrane under tile typically lasts the life of the tile floor – 20 years or more. Lifespan in a Westminster addition comes down to installation quality, since the membrane itself doesn’t wear out, but a bad bond coat can fail within 18 to 24 months.
Yes, in most cases. If the failure is localized to one shower or one section of floor, we isolate the affected area, remove the tile and membrane there, and rebuild with the correct Schluter system – the rest of the addition stays intact. A broad failure across a whole floor usually means a full rebuild.
A single shower or bathroom wet-area repair takes 3 to 7 days including tile cure and membrane set time. A larger floor or a bathroom-plus-laundry rebuild runs 1 to 2 weeks. We schedule around your household and give you the duration in writing before work starts.
We source Schluter membranes, KERDI-BOARD, and drain assemblies through authorized suppliers who carry current stock, matched to the series stamped on your existing roll or panel. We don’t carry Schluter product on any truck and don’t claim to – the material arrives for your specific job. Bradford Remodeling Co Westminster is an independent service provider and is not affiliated with Schluter Systems.
For additions and ADU work that touches cabinetry or surfaces, we also install KraftMaid, Cambria, and Silestone, among other documented brands.
Get a Written Price for Your Westminster Schluter Project
If your Westminster addition or ADU has a wet area that needs attention, or you’re planning a build and want the Schluter system done right the first time, call (833) 954-5086 for a free estimate. You’ll get a written price before any tool comes out, the scope and guarantee spelled out, and a clean site when we’re done – squared away and signed off.
Written by the team at Bradford Remodeling Co Westminster, serving Westminster and nearby areas.












