







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
James Hardie Bathroom Remodeling: The Westminster Owner’s Guide
We install James Hardie-compatible bathroom remodeling in Westminster, and a full bath typically runs $9,000 – $28,000 depending on size, tile layout, and whether the wet wall gets rebuilt. If you’ve found soft drywall around the shower valve, paint blistering on the ceiling below, or hairline cracks spreading from the tub deck, that’s not cosmetic wear. It’s water reaching the substrate. James Hardie’s fiber-cement and tile backer products are meant to stop exactly that in Westminster’s damp coastal air, and when they’re installed wrong – wrong fastener, wrong gap, wrong board for the wet zone – the failure shows up at the finish surface first and inside the wall second.
We’re an independent remodeling company, not affiliated with James Hardie. What we do is specify and install their bathroom-rated boards correctly, put the price in writing before demolition, and back the finished work with the 365-Day Done Right Promise.
Which James Hardie Models This Applies To

The core bathroom product here is HardieBacker, the fiber-cement tile backer, sold in 1/4-inch (floors, over a solid subfloor) and 1/2-inch (walls) panels. It’s a different product from the HardiePlank lap siding that goes on your exterior, and mixing the two up is the single most common ordering mistake we see. HardieBacker carries a printed label on the back of each sheet with the thickness, board dimensions, and the manufacturer’s fastening and joint guidance – read that label, because it names the specific screw type and the required gap between sheets.
If your home has exterior tile or a wet-area panel identified as “HardiePanel,” that’s a vertical siding product, not a backer. Match the product name on the label to the application before you price anything. On the OEM-versus-aftermarket call: there’s no proprietary electronics or series-fit problem here the way there is with appliance parts. A generic cement backer board is not the same spec as HardieBacker – the fiber-cement density, water absorption, and fastener holding differ – and in a shower wall that difference is the whole job. We buy the genuine board. Where we’ll substitute a documented equivalent is on setting materials, fasteners, and valves (Moen or Kohler trim, for instance), and we name the brand on the written quote so you know exactly what’s going in the wall.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Signs Your James Hardie Bathroom Remodeling Is Failing
- Soft or crumbly drywall just outside the shower enclosure. Water is bypassing the backer or a seam was never taped and sealed. By the time the paint feels spongy, the board behind it has already lost its strength.
- Screw heads popping through the tile or grout every few feet. The backer wasn’t fastened to the framing per the manufacturer’s pattern, or framing lumber shrank and pulled the panels loose. Westminster’s older housing stock has plenty of 2×4 framing that has moved since the 1950s and 1960s.
- Grout cracking along a straight vertical line. That’s a board joint. Sheet-to-sheet gaps were butted tight instead of held open and filled, so the two panels fight each other every time someone leans on the wall.
- Musty smell in the bathroom that returns after cleaning. Moisture is trapped in the wall cavity. This is the symptom owners notice last and should act on first.
- Paint blistering or a watermark on the ceiling of the room below. The pan or the lower wall has failed. In a Westminster condo or a home with a second-floor bath over a garage, this is where you find it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included

Bathroom remodeling in Westminster runs $9,000 – $28,000 installed. A smaller bath lands $5,000 – $12,000. If the wet wall is the scope, a walk-in shower installation is $4,500 – $12,000 and a tub-to-shower conversion is $3,500 – $10,000. Shower replacement alone is $3,000 – $8,500, and a vanity install is $800 – $3,000.
What moves the number: how much failed board has to come out, whether the framing is soft, tile selection, and whether the valve and drain get replaced while the wall is open. We price parts and labor separately on the written quote so you can see what the HardieBacker and setting materials actually cost. Nothing moves at the door. Every completed project carries the 365-Day Done Right Promise – if our installation fails inside that window, we come back and correct it at no charge.
DIY or Call Us?
You can safely pull the escutcheon plate off the shower valve and look for moisture, press the drywall near the enclosure with your thumb, and check the ceiling below for stains. Stop there. Opening a wet wall on a live plumbing rough-in means water and sometimes electrical in the same cavity, and cutting out backer board without knowing what’s behind it is how a small repair becomes a gut.
If you’re set on doing the work yourself, the genuine articles to read are the HardieBacker installation manual and your local building department’s requirements for a shower pan and waterproofing. That’s not a job we’d hand a homeowner, and we’d rather tell you that straight than take a callback. Call (833) 954-5086 and we’ll give you an honest read and a written price.
FAQs

How long does HardieBacker last in a Westminster bathroom? Installed correctly, a fiber-cement backer panel lasts the life of the tile over it – easily 25 years or more. The failure isn’t the board; it’s the seams, the fasteners, and the waterproofing at the pan and valve. Westminster’s salt air and marine layer keep interior humidity higher than inland markets, so ventilation and a proper exhaust fan matter as much as the board itself.
Can it be repaired instead of replaced? Sometimes. A single cracked board seam or a failed screw pattern can be re-taped and re-waterproofed if the board is still sound and dry. Once the panel is soft or the framing behind it is wet, it comes out. We check with a moisture reading before we quote either way. Call (833) 954-5086 for a free estimate.
How long does the swap take? A shower wall rebuild is typically three to five working days once materials are on site and inspection is scheduled – demolition, board, waterproofing, then tile and cure time. A full bathroom remodel runs two to four weeks. We put the schedule in writing with the price so there are no surprises mid-job.
How do you source the part? We buy genuine HardieBacker through documented suppliers and list the product, thickness, and setting materials on the quote. Substitutions happen only with your sign-off in writing. We also install KraftMaid, Cambria, and Silestone in the same bath if you’re replacing cabinetry and counters while the wall is open.
Bradford Remodeling Co Westminster gives you a written price before any work starts, background-checked and uniformed technicians on every job, and a real person on the phone around the clock. Call (833) 954-5086 for a free estimate. Your signed written guarantee is in your hand at close, and our technicians bring up to 22 years of experience to the work.
Written by the team at Bradford Remodeling Co Westminster, serving Westminster and nearby areas.












